|
Dynalco M951 Hall Effect Speed Sensor
Dynalco M951霍尔效应速度传感器
Dynalco Active Powered - Ordinary Area有源磁传感器 - 普通区域应用
Dynalco Magnetic Pickups Speed Sensors 磁传感器速度传感器
该霍尔效应传感器旨在检测含铁材料（齿轮齿，孔或销），以进行低至零速的速度测量。数字输出与大多数PLC输入卡兼容。该传感器的作用距离很远（4.500英寸），螺纹为5 / 8-18。This hall effect sensor is designed to sense ferrous material (gear teeth, hole or pin) for speed measurement down to zero-speed. The digital output is compatible with most PLC input cards. This sensor has a long reach (4.500 inches) and a 5/8-18 thread.
Dynalco M951 Hall Effect Speed Sensor 
Dynalco M951 Hall Effect Speed Sensor
M951
M951 - 5/8-18 x 4.5
5/8-18 x 4.5" - 3 Pin
Active (Powered) - Ordinary Area
Zero Speed Hall-Effect Sensors
Datasheets
Dynalco M951 Hall Effect Speed Sensor Datasheet
Miscellaneous
Dynalco Rep Locator
Magnetic Pickup Look-up
Details
M951
M951-5 / 8-18 x 4.5
5 / 8-18 x 4.5“-3针
有源（有源）-普通区域
零速霍尔效应传感器
数据表
Dynalco M951霍尔效应速度传感器数据表
杂
Dynalco Rep定位器
磁性传感器
细节
该霍尔效应传感器旨在检测含铁材料（齿轮齿，孔或销），以进行低至零速的速度测量。数字输出与大多数PLC输入卡兼容。该传感器的作用距离很远（4.500英寸），螺纹为5 / 8-18。This hall effect sensor is designed to sense ferrous material (gear teeth, hole or pin) for speed measurement down to zero-speed. The digital output is compatible with most PLC input cards. This sensor has a long reach (4.500 inches) and a 5/8-18 thread.
SPECIFICATIONS:
POWER SUPPLY: 8 TO 32VDC.
SUPPLY CURRENT: 30 mA MAXIMUM
OPERATING TEMPERATURE: -30 F TO +250 F (-35 C to 125 C)
SENSED FREQUENCY: 0 TO 20 KHZ
OUTPUT VOLTAGE: SQUARE WAVE.
LOGIC 0: WHEN NEAR FERROUS MATERIAL, ACTIVATES SENSOR.
* +0.5V AT ≤ 50mA.
LOGIC 1: WHEN NO FERROUS MATERIAL PRESENT
* FOR Vin ≤ 24V USE A PULL UP RESISTOR ≥ 1KΩ
* FOR Vin ≤ 16V USE A PULL UP RESISTOR ≥ 330Ω
INSULATION RESISTANCE: 100 MEGAohm MIN. AT 50 VDC (COMMON TO HOUSING)
HOUSING: 303 STAINLESS STEEL, BLIND END.
规格：
电源：8至32VDC。
电源电流：30 mA
工作温度：-30 F至+250 F（-35 C至125 C）
感应频率：0至20 KHZ
输出电压：方波。
逻辑0：当靠近铁质材料时，激活传感器。
* + 0.5V AT≤50mA。
逻辑1：当没有含铁材料PRESENT
*于VIN≤24V USE上拉电阻器≥1KΩ
*于VIN≤16V USE一个上拉电阻≥330Ω
绝缘电阻：100兆欧。50 VDC时（常见于外壳）
外壳：303不锈钢，盲端。
|
